Maxim-integrated MAXQ7666 Bedienungsanleitung Seite 351
- Seite / 386
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
MAXQ7665/MAXQ7666 User’s Guide
14-14
MOVE dst,
src
Move Data
Table 14-3. Destination Specifier Codes
Data Transfer dst (16-bit) ← src (16-bit): dst[15:0] ← src[15:0]
Rules dst (8-bit) ← src (8-bit): dst[7:0] ← src[7:0]
dst (16-bit) ← src (8-bit): dst[15:8] ← 00h *
dst[7:0] ← src[7:0]
dst (8-bit) ← src (16-bit): dst[7:0] ← src[7:0]
*
Note: The PFX[0] register may be used to supply a separate high-order data byte for this type of transfer.
dst
dst BIT ENCODING
(ddd dddd)
WIDTH
(16 OR 8)
DESCRIPTION
NUL 111 0110 8/16
Null (Virtual) Destination. Intended as a bit bucket to assist
software with pointer increments/decrements.
MN [n] nnn 0NNN 8/16
nnnn Selects One of First 8 Registers in Module NNN; where
NNN= 0 to 5. Access to Next 24 Using PFX[n].
AP 000 1000 8 Accumulator Pointer
APC 001 1000 8 Accumulator Pointer Control
PSF 100 1000 8 Processor Status Flag Register
IC 101 1000 8 Interrupt and Control Register
IMR 110 1000 8 Interrupt Mask Register
A[n] nnn 1001 8/16 nnn Selects 1 of First 8 Accumulators: A[0]..A[7]
Acc 000 1010 8/16 Active Accumulator = A[AP]
PFX[n] nnn 1011 8 nnn Selects One of 8 Prefix Registers
@++SP 000 1101 16 16-Bit Word @SP, Pre-Increment SP
SP 001 1101 16 Stack Pointer
IV 010 1101 16 Interrupt Vector
LC[n] 11n 1101 16 n Selects 1 of 2 Loop Counter Registers
@BP[OFFS] 000 1110 8/16 Data Memory @BP[OFFS]
@BP[++OFFS] 001 1110 8/16 Data Memory @BP[OFFS]; Pre-Increment OFFS
@BP[--OFFS] 010 1110 8/16 Data Memory @BP[OFFS]; Pre-Decrement OFFS
OFFS 011 1110 8 Frame Pointer Offset from Base Pointer (BP)
DPC 100 1110 16 Data Pointer Control Register
GR 101 1110 16 General Register
GRL 110 1110 8 Low Byte of GR Register
BP 111 1110 16 Frame Pointer Base Pointer (BP)
@DP[n] n00 1111 8/16 Data Memory @DP[n]
@++DP[n] n01 1111 8/16 Data Memory @DP[n], Pre-Increment DP[n]
@--DP[n] n10 1111 8/16 Data Memory @DP[n], Pre-Decrement DP[n]
DP[n] n11 1111 16 n Selects 1 of 2 Data Pointers
2-CYCLE DESTINATION ACCESS USING PFX[n] REGISTER (See Special Notes)
SC 000 1000 8 System Control Register
CKCN 110 1000 8 Clock Control Register
WDCN 111 1000 8 Watchdog Control Register
A[n] nnn 1001 16 nnn Selects 1 of Second 8 Accumulators A[8]..A[15]
GRH 001 1110 8 High Byte of GR Register
Maxim Integrated
- Functional Diagrams 1
- 1.1 Overview 7
- 1.1.2 Instruction Set 8
- 1.1.4 Register Space 8
- 1.2 Architecture 9
- 1.2.1 Instruction Decoding 10
- 1.2.2 Register Space 11
- 1.2.3 Memory Organization 13
- 1.2.3.2 Utility ROM 16
- 1.2.3.3 Data Memory 16
- 1.2.3.4 Stack Memory 17
- 1.2.3.7 Data Alignment 19
- CDA0 = 1 21
- 1.2.4 Interrupts 25
- 1.3 Programming 31
- 1.3.6.1 Sign Flag 37
- 1.3.6.2 Zero Flag 38
- 1.3.6.3 Equals Flag 38
- 1.3.6.4 Carry Flag 38
- 1.3.6.5 Overflow Flag 39
- 1.3.7.2 Unconditional Jumps 39
- 1.3.7.3 Conditional Jumps 40
- 1.3.7.4 Calling Subroutines 40
- 1.3.7.5 Looping Operations 40
- 1.3.8 Handling Interrupts 41
- 1.3.9 Accessing the Stack 42
- 1.3.10 Accessing Data Memory 43
- 1.4.19 General Register (GR) 59
- 2.1 Architecture 75
- 2.3 Supply Configuration 83
- 2.4 Linear Regulator 84
- 2.5 Power-On Reset 84
- 2.5.1 Power-Up Counter 85
- 2.5.3 Reset Output 87
- 2.7 Reset Mode 89
- 2.7.2 External Reset 90
- 2.7.3 Internal System Reset 90
- SECTION 3: ANALOG I/O MODULE 91
- 3.1.1 Analog I/O Pins 96
- Register Name: ACNT 98
- ADCMX2 ADCMX1 FUNCTION 99
- 1 1 Reserved 99
- Maxim Integrated 100
- Section 5 104
- Section 2 104
- Section 3.3.6 107
- Section 3.4 107
- Table 3-2. ADC Signals 108
- Section 3.3.10 110
- 3.3.4 Unipolar/Bipolar 111
- 3.3.5 Transfer Function 112
- Section 3.3.3 115
- Section 3.3.5 115
- 3.3.7 Analog Input Protection 116
- 3.3.8 ADC Clock 117
- 3.3.9 Auto Shutdown Mode 117
- 3.3.11 ADC Interrupts 122
- 3.3.12 Using the ADC 123
- 3.4 Temperature Sensor 124
- Sections 15 125
- TEMPERATURE (°C) 126
- Section 3.4.2 127
- Table 3-12. DAC Signals 128
- 3.5.4 DAC Power-Down 130
- 3.5.5 Using the DAC 130
- LIST OF FIGURES 133
- LIST OF TABLES 133
- 4.1 Architecture 134
- 4.2 CAN Controller Registers 136
- 4.3 CAN Operations 177
- 4.3.1.2 Remote Frame 180
- 4.3.1.3 Error Frame 181
- 4.3.1.4 Overload Frame 181
- 4.5 External Pins 182
- 4.7 CAN Interrupts 183
- 4.8.1 Message Center 15 185
- 4.9.2 Receiving Data Messages 186
- 4.15 Bit Timing 194
- 4.16 CAN Bus Activity 197
- 5.1 Architecture 200
- Section 3 204
- 76543210 205
- Reset 0 0 1 0 0 0 0 1 205
- Access rw r r rw rw rw rw rw 205
- 5.3 System Clock Generation 209
- 5.4 Watchdog Timer 215
- 5.5 Power Management Mode 217
- 5.5.2 Switchback Mode 218
- 5.5.3 Stop Mode 218
- SECTION 6: SERIAL I/O MODULE 219
- 6.1.1 UART Pins 223
- 6.2 UART Registers 223
- Serial Mode Definition 224
- — — — — — — — 226
- 6.3 Modes of Operation 227
- 6.3.3 UART Mode 2 230
- 6.3.4 UART Mode 3 230
- 6.4 Baud-Rate Generation 233
- 6.4.4 Baud-Clock Generator 234
- 6.5 Framing Error Detection 235
- 7.1 Architecture 238
- Compare Mode: 244
- Capture Mode: 244
- 7.2.3 Type 2 Reload Registers 248
- 7.3.3 16-Bit Counter 255
- 7.3.4 Dual 8-Bit Timers 256
- 7.4.3 Measure Period 259
- 8.1 Architecture 264
- 8.1.1 Port Pins 265
- 8.2 Port Registers 265
- 8.3 GPIO Operation 271
- 8.3.4 Port Pin Examples 273
- 9.1 Architecture 276
- 9.1.1 SPI Pins 277
- 9.2 SPI Peripheral Registers 277
- 9.3 SPI Operation 282
- 9.3.2 SPI Slave Operation 283
- 9.3.3 SPI Transfer Formats 284
- 9.4 SPI Transfer Baud Rates 285
- 9.5 SPI System Errors 285
- 9.6 SPI Interrupts 286
- 10.1 TAP Overview 289
- 10.2 Architecture 289
- 10.2.1 TAP Pins 290
- 10.3 TAP Interface Control 291
- 10.4 TAP Controller Operation 292
- 10.4.2 Run-Test-Idle 293
- 10.4.3 IR-Scan Sequence 293
- 10.4.5 Communication via TAP 294
- 11.1 Architecture 299
- Section 12 303
- Section 10 305
- Section 1 305
- 11.3 Debug Engine Operation 306
- 11.3.2 Breakpoint Registers 308
- 11.3.3 Using Breakpoints 310
- 11.3.4 Debug Mode 311
- 11.3.5 Debug Mode Commands 311
- 11.3.8 Return 313
- 12.1 Bootstrap-Loader Mode 317
- Section 11 318
- Section 12.5 320
- 12.5 JTAG Bootloader Protocol 321
- 13.6 Operand Count Selection 335
- 13.8 Accessing the Multiplier 336
- Acc.<b> 343
- 1000 1010 0001 1010 345
- 1101 1010 0010 1010 346
- 0011 1100 ssss ssss 349
- 0111 1100 ssss ssss 349
- 1111 1010 bbbb 1010 352
- 1101 1010 0000 1010 353
- 1110 1010 bbbb 1010 353
- 1101 1010 0001 1010 354
- 1ddd dddd 0bbb 0111 354
- 1ddd dddd 1bbb 0111 354
- 1000 1010 1001 1010 355
- .<b> 356
- 1110 1100 0000 1101 359
- 1001 1100 0000 1101 359
- 1101 1100 0000 1101 359
- 1100 1100 0000 1101 359
- 1000 1100 1000 1101 360
- 1010 1100 1000 1101 360
- 1110 1100 1000 1101 360
- 1001 1100 1000 1101 361
- 1101 1100 1000 1101 361
- 1100 1100 1000 1101 361
- 1000 1010 0100 1010 362
- 1000 1010 0101 1010 362
- 1000 1010 1100 1010 363
- 1000 1010 1101 1010 363
- 1000 1010 0010 1010 364
- 1000 1010 0011 1010 364
- 1000 1010 0110 1010 364
- 1000 1010 1010 1010 365
- 1000 1010 1111 1010 365
- 1000 1010 1110 1010 366
- 1000 1010 1011 1010 366
- 1000 1010 0111 1010 368
- 1000 1010 1000 1010 368
- 1011 1010 bbbb 1010 369
- WITH TYPE A FLASH) 371
- 15.2 Data Transfer Functions 372
- TYPE F FLASH) 378
- 16.2 Data Transfer Functions 383
- REVISION HISTORY 386
Verwandte Produkte und Handbücher für Hardware Maxim-integrated MAXQ7666
Hardware Maxim-integrated MAXQ Family Users Guide: MAXQ8913 Supplement Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Hardware Maxim-integrated High-Speed Microcontroller Users Guide: DS80C390 S Bedienungsanleitung
(158 Seiten)
(158 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern